Heat-Timer® ETV/ETS – Now Saving Time as well as Money..

 


For plumbing professionals, time IS money.  The longer a job takes, the longer your guys are tied up and can’t get to the next job. Or you have to bid the expected time so high that you never get the job in the first place.

Heat-Timer® has been helping commercial plumbers for decades by providing them high quality solutions for domestic hot water systems. The most current evolution of our 3-way mixing valve, we call our ETV or Electronic Tempering Valve. This motorized mixing valve is driven by a control module that utilizes an immersion sensor to control the mix of hot and cold water to maintain a desired mixed outlet temp +/- 2 degrees. With our computer guided ETV running the show, you can keep your hot water supply heated hot enough to be safe from bacteria (See Table Below) like Legionella, while delivering a perfectly controlled hot water temperature to end users. 

Heat-Timer’s ETV Now Delivered Inside the ETS

The Heat-Timer Electronic Tempering Valve (ETV) has been an industry standard valve for reliability and accuracy for many years. It’s a go-to for most commercial plumbers that have been around a while. But what many of them still don’t know is that the ETV is now available as part of the Electronic Tempering Station (ETS). This is a pre-plumbed ETV solution available in multiple piping sizes from 1 ½ inch to 4 inch piping. The entire goal of the ETS is to provide a ready to go solution for valve replacement that requires nothing more than hot and cold water connections and some A/C for the ETV Controller. Field experience has shown that the ETS saves many hours of time at the jobsite, in some cases allowing a complete switchover to the ETS solution in only a few hours. 

The ETS is a completely pre-wired, pre-plumbed solution including all unions, isolation valves, sensors and check valves that would be required in a first rate field installation. For added protection, the ETS assembly is configured to shut off the hot water supply to the mixing valve on loss of power or if the mixed outlet temperature exceeds the Alarm Limit. It does that by operating a separate High Temp Limit valve located on the hot water supply.

The assembly is compact and saves plumbers many hours of painstaking work while decreasing downtime of the hot water supply to the building being retrofitted. It is extremely cost effective and even comes in a duplex configuration built for high GPM requirements or critical installations requiring redundancy.

You do the math but we’re pretty sure that if you’re bidding large jobs for apartments, hotels, or hospital conversions, you’ll be at a competitive advantage if you bid with Heat-Timer’s Electronic Tempering Station. The ETS is simply the most economical, high-tech, and most efficient integrated DHW solution to bid on your next job.  

And don’t forget about the new ETS-LT, the wall mounted lower cost version of our ETS for simplex (single valve) configurations, for saving even more time/money on your DHW installations. 

Features of the ETS-LT

  • Completely prewired and pre-plumbed ETV suitable for wall mounting
  • Simplex configurations only
  • 6 Valve Sizes ranging from ¾” to 2 ½”
  • Safety hot water shutoff on loss of power or alarm conditions
  • Strong Unistrut frame for flexible wall mounting.
  • All unions, isolation valves and sensors included
  • Extremely accurate and safe hot water delivery.

Call the folks at Heat-Timer® for more information at (973) 575-4004. 

https://www.heat-timer.com

Original Source: https://www.heat-timer.com/heat-timer-etv-ets-now-saving-time-as-well-as-money/

Comments

Post a Comment

Popular posts from this blog

How Heat-Timer® Controls Can Make Your Building Management System Better

A  Building Management System  (BMS), also called Building Automation System (BAS) is a system that allows building managers to monitor and control a building’s major mechanical and safety systems in one central, easy-to-use application. A BMS can be thought of as a distributed network of building systems supervised and controlled in one central platform. The network of field controllers and other system controllers are distributed throughout the building and communicate to the BMS through a local area network. Field controllers can be general purpose, supplied by the BMS integrator and used for simple applications like lighting control, ventilation fans and building access. With a BMS, these applications can also be separated by zone, floor or other combinations to yield optimal HVAC performance. Field controllers for mission critical systems like fire alarms and heating are specialized and can act independently, as well as under BMS control. The Heat-Timer® Platinum se...
Read more

Water Safety For all Time

Image
Because of regulations put in place after the outbreak of legionnaire’s disease in the 90’s, installation of Domestic Hot Water (DHW) systems were changed for the sake of public safety.  All DHW systems, whether storage based or tankless, must now meet the conflicting requirements of holding DHW at a minimum of 140°F (60°C) to comply with such standards as OSHA Technical Manual Section 3 Chapter 7, to combat Legionella growth, while delivering hot water at a temperature that prevents scalding injuries in sinks and other fixtures. For decades, commercial plumbing installers have embraced a 3 way mixing valve or “tempering valve” as the perfect solution to the dilemma. Early tempering valves were controlled manually with fixed setpoints, but in 2020 we have evolved to using motorized valves under the direction of a standalone electronic control station that adds flexibility, reduces energy use, provides alerts and alarms, and generally improves the safety of any domestic ...
Read more

Heat-Timer’s Wireless Sensor Integration Just got a Big Upgrade

Image
  One of the most appealing parts of the Heat-Timer® Platinum Series is the wireless sensor connectivity that comes with our Building Net internet upgrade. There are thousands of clients who own an original, non-internet capable Platinum Series control and when they upgrade the control with our Building Net internet package they actually get two major elements: An Internet/Mobile ready control – The Building Net upgrade gives any platinum control the ability to be controlled via the internet through a simple browser connection to a web management portal, or via our free mobile app. In either case, reports, alarms, control settings, and real-time monitoring are all at your fingertips, wherever those fingertips may be. Wireless Sensor Integration – You can think of this as the second network access that is enabled by the Building Net upgrade. This internal Long Range network allows you to connect our wireless space sensors to the control, which by reporting temperatures in vari...
Read more